Model 28600

Model 28600

Quick set up instructions: Welcome to the world of radio controlled timekeeping technology. We hope you will enjoy the convenience of never having to set your clock again and the confidence of knowing exactly what time it is.

Insert 1 fresh AA, LR6 1.5 volt ALKALINE battery according to the polarity marked on the case

Place the clock in a window overnight with the face of the clock pointing toward Colorado. Allow the clock to set itself to Pacific time before pressing any buttons. If the clock does not set overnight, allow it another night to set itself. Poor weather or atmospheric disturbance can interfere with the clock picking up the signal.

If you do not live in the Pacific time zone, then press the button to select your time zone.


Note: When the battery is installed the second hand will advance eight seconds (two seconds per step x four steps).

The clock is now searching for a signal. For the initial setting it is recommended to stand the clock in an upright position near a window. Within five minutes the clock will either receive the WWVB signal and set itself to the exact time, or it will determine that the signal is not receivable at its current location and time of day. If a signal is not receivable it will fast-forward the hands to the 4, 8, or 12 o’clock position and search for WWVB each hour until a signal is received. If the time is manually set the clock will continue to periodically search for a signal and automatically reset the hands when the signal is received.

For a better understanding of how and why your clock works please continue reading.

Nothing is more precisely measured than time!

Since the beginning of time, man has been fascinated with the measurement of time and has devised more accurate machines to trap and measure time. Today, time is precisely measured in the United States by the most accurate clock in North America, the Atomic Clock of the US National Institute of Standards and Technology, Time and Frequency Division in Boulder, Colorado. A team of atomic physicists continually measures every second of every day to an accuracy of ten billionths of a second per day. These physicists have created an international standard, measuring a second as 9,192,631,770 vibrations of a Cesium 133 atom in a vacuum. This atomic clock regulates the WWVB radio transmitter located in Fort Collins, Colorado, where the exact time signal is continuously broadcast throughout the United States at 60 kHz to take advantage of stable longwave radio paths found in that frequency range. Radio waves at these low frequencies use the earth and the ionosphere as a wave-guide and follow the curvature of the earth for long distances.

The built in antenna system will receive the WWVB signal anywhere in North America within 2000 miles of Fort Collins where long-wave radio reception is undisturbed. A microprocessor activates the receiver and processes the time signal from Fort Collins overnight.

Through the radio signals, Skyscan radio controlled clocks always keep precise time. The changeover from standard time to daylight savings time, and vice versa, takes place automatically with the same precision.

Additional details: To set up your clock simply install one fresh AA, LR6 ALKALINE battery. Due to the nature of long wave radio signals it is normally not possible to receive a signal during the day so it is best to install the battery late in the evening. Select your time zone by pressing one of the four time zone buttons

PT-Pacific Time

MT-Mountain Time

CT-Central Time

ET-Eastern Time

If no time zone is selected the clock will default to Pacific Time. Another time zone can be selected after the clock has set itself. Your clock can only set itself to one of the four time zones stated above. For time zones outside of PT, MT, CT or ET you must manually set the time using the Manual Time set button on the back of the movement.

Select a location to place your radio controlled clock here it will be at least six feet away from a TV, computer, air conditioner or other household electrical appliances. The optimal location is near a window. Windows facing Colorado provide the best signal. The WWVB time signal will easily penetrate masonry and wood framed buildings. WWVB will penetrate almost every residential building and most steel buildings if they have adequate windows. It is not possible, however, for WWVB to penetrate most indoor shopping malls and rooms in the center of large office buildings that do not have windows. In buildings that WWVB cannot penetrate you may set the time using the manual time set button. When the clock is exposed to the WWVB signal it will automatically set the hands to the exact time.

Skyscan clocks do not receive or process radio controlled time signals from Germany’s DCF 77, Japan’s J Ga AS, or England’s MSFs atomically regulated transmitters. Skyscan clocks can be manually set and used anywhere.

For more information on the NIST and radio controlled time, see

Set the time using the Manual Time Set button: In some cases, the Skyscan clock may not receive the WWVB signal due to atmospheric disturbances or hard to reach locations such as inside malls. In this case, please use the Manual Time Set button, located at the back of the clock to manually set the time. To do this:

1. Press and hold the Manual Set button. 2. The minutes and seconds hands will fast-forward. The seconds’ hand will stop at 12. The minute’s hand will keep advancing. 3. Keep holding the Manual Set button until the time is set as required. 4. Release the button.

Note: The clock will continuously search for WWVB each hour until a signal is received. Once the WWVB time signal is received, the WWVB time will override the manual set time.

Troubleshooting The wonderful advantage of owning a Skyscan radio controlled clock is that it is virtually trouble free. If the clock receives a clear signal it will set itself perfectly. If it does not receive a signal consider the following:

Battery – The Skyscan clock must have a fresh battery to receive and process the time signal. Location – Try a different location, ideally near a window. It should be at least six feet from computers, TVs, air conditioners, other Radio-Controlled clocks and other electrical appliances that cause interference. Weather – Electrical storms between you and Colorado during the night will interfere with the WWVB signal.

Daylight Savings Time The National Institute of Standards and Technology and WWVB encode a special DST “bit” in the WWVB transmission for DST. Your Skyscan clock will read this information and automatically advance the hands one hour in the spring and eleven hours in the fall. Arizona and Indiana If you live in an area that does not recognize DST you must press the (unmarked) DST button for one second to deactivate your clock’s DST program. To reactivate the DST program simply press the DST button again for one second.

Frequently Asked Questions

Q. How long will the battery last? A. A good AA alkaline battery will last over one year. If your clock is located in an area with little interference where it can quickly receive a signal the battery will last much longer than one year.

Q. Can the clock be wired to control timing circuits? A. No.

Q. Why does the second hand move only once every two seconds, but it moves two seconds per step? A. When the battery drops below 1.25 volts the clock indicates that it is time to change the battery by advancing the second hand in two second steps. The operating voltage range is 1.25 to 1.75 volts.

WARRANTY: This product is warranted to be free of defects in manufacturing for 1 year after purchase from Sam’s Club.This model is discontinued and no longer eligible for the manufacturer’s warranty. Defective clocks should be returned to the place of retail purchase.

BATTERIES CHANGE: For best performance, batteries should be replaced at least once a year to maintain the best running accuracy. Ensure that the batteries used are new and the correct size.Please help in the preservation of the environment and return used batteries to an authorized depot.

Comments are closed.